How do I cancel a session I created ?

I think a good addition to the platform would be to start a Musicians Wanted Bulletin Board where jammers can find other jammers to create groups for jamming.  There should be the ability to respond to the thread.  

Also the Upcomimng Sessions page should be edited as it is littered with old posts and numerous duplicate posts.

Hi,

I‘ve tried all available Asio versions and drivers provided by focusrite for Windows 10, but I always keep getting a very crackling sound. It sounds like you’re scratching over a record.

The issue starts with the test sound on the audio gear setup. It already crackles. In the jam sessions sometimes it‘s better sometimes it‘s worse. But never good. 

I‘ve tried all different sample rates (mostly 96k as suggested here in the forum) and low and high buffer rates. I‘ve tried all frame sizes. I‘ve contacted the Focusrite support and JamKazam Support. 

Focusrite support says „Yes, we keep getting contacted by 2i2 3rd gen users with this. We‘ve reached out to JamKazam and offered them a free device so they can test and get it fixed.....but JamKazam just stopped answering our e-mails.“

I‘ve asked Jamkazam support if there is a known issue with the 2i2 3rd gen. They said they don’t know because they don’t have a device. Well, guys, Focusrite is offering you a free device. Just go ahead and answer their e-mails.

Focusrite support also says that they suspect the issue with how Jamkazam deals with ASIO Frame rates. While ASIO deals with „frames“ Jamkazam expects „Milliseconds“. (Or the other way around, don’t know anymore). 

1. Does anybody have a clue how to fix this?
2. Anybody an idea why the JamKazam Team would refuse to cooperate with Focusrite to sort this out?

On MAC using Apogee Duet as interface I experience audio interference when I add video.  Anybody else have this problem?

I can't find a way to delete upcoming scheduled sessions in JKZ (including recurring ones). Any help much appreciated.

Is there a setting so that session invitations will stay on your screen longer ?
Theyd disappear after about four seconds and if I'm looking in a different direction I just miss it

Hi
   I'm a nerd.....but getting this to work is grrrrr   I have years as a Pro PC mavin and Pro Musician, and Pro DJ
I'm using W7 (SSD ,  I5 @ 2.6 with 12gigs ram) a Focusrite 2i4 ( have 2 of them  V1 and V2) ( newest dirver), and use them Professionally with 0 problems 
I use Guitar rig 5 in my act with 100% pleasure and zero problems
I use Loops and Full songs to play over with no problems

I use Presonus and Cakewalk DAW....works great
I'm in NYC Metro with a great Cable INet system ( Optimum)

So now I'm venturing into your realm :-)



Only 1 out of 10 times have I gotten to full Green, ...............   grrrrrrr
I wanted to try using Guitar Rig to play a background track and I'd play along as a typically do.........and no dice
then it was back to setup failure upon failure ! grrrr

can anyone please HELP  :-) !!!

What Sample Rate ?
and what Bit Rate please ?

The Focusrite keeps reverting to a high bit rate?

Hi everybody,
as I had input latency and input-jitter problems with my Scarlett 2i2 3rd Gen, I looked after a new Driver version and hoped that the problem was solved.

After the upgrade the interface shows a latency of 20ms in Jamkazam and failed the test. So it is not more usable in Jamkazam.
I opened a ticket at focusrite support and they said the problem is adressed to the developers and they have no clue yet. I shall wait for a new sw-Version

Does anybody has the same problems?

I warn you not to upgrade to 3.6.0

Best regards
HC

PS: I regret buying this stuff 

Still trying to figure out to get JK to run using sound from Logic Pro X 10.5.   

A few minutes ago.  I signed in and tried to change the audio and out channels.   I made sure the Aggregate Device and Black Hole to Output devices were set up OK and highlighted on the Mac under audio settings.

I tried to verify the channels were set up correctly, attempting to change one of the input channels.   I tried to change the audio inputs from channels 1 and 2 to 3 and 4, but  when  as I deleted channel 1, a message popped up saying I need to identify 4 channels.   It wouldn't set me change, nor set new, channels.   


What do I need to do differently, please?


Also, the instrument display was blank and would not let me input the name of the instrument.   I've not seen this happen before.    Consequently, I was unable to continue  trying to connect  and attempt a test recording.

Thanks, 


Nick Costa

(These steps also apply to the Camera settings, for Video)

Issue. When in a Session there is no sound. The Audio Interface shows a signal and the My Live Tracks LED signal indicators are not detecting any signal. The Audio Device settings are correct.

Later versions of MacOS include Privacy settings that control access to the Microphone in order to process audio. This is required for applications to receive audio from the interface source

When launching JamKazam for the first time you may encounter an alert option to allow JamKazam to access the microphone. Click Yes!.

If you clicked Later, you may not see the alert again and will need to enable the option in Security & Privacy setting:

System Preferences>Security & Privacy; Privacy Tab.  For the Microphone, make sure JamKazam is checked.

You will be prompted to quit and restart JamKazam for the change to take effect.  You may need to repeat this step to begin hearing Audio in the session.

Where should I hear Audio after enabling JamKazam in the Privacy Settings? Assuming your Audio Interface is setup correctly in the JamKazam audio device settings, the audio output will be routed from JamKazam back to your Interface main out. Commonly, the Headphone Jack. Unless you specified another monitoring output from your Audio Interface using its own application.

Video Settings (These same steps apply to the Camera settings, for Video) 
System Preferences, click Security & Privacy, then click Privacy. Select Camera. Select the tickbox next to an app to allow it to access your camera. Deselect the tickbox to turn off access for that app.