HELP NEEDED--How to set up port forwarding: Apple AirPort Extreme

[nycbassguy@gmail.com]

Hi everyone, hoping to get some help here. Joined JK a few weeks ago and had limited success with audio. I've combed thru every available resource i can find on this site and others, but i'm still having difficulty setting up port forwarding on my airport to solve the 'no audio' issues i always run into. also getting the warning that my network changes packets/port numbers when i boot up the app. here's what i have so far:

GEAR
iMac running 10.12.6
Apogee ONE interface
Apple Airport Extreme (w/Ethernet)

-- on PortChecker, the ISPs match so that's 👍
-- Router Mode: DHCP and NAT
-- Port Settings: I set up an IPv4 port mapping setting and named it JK (duh)
Public UDP Ports: 12000
Public TCP Ports: 12000
Private IP Address: 10.0.1.201
Private UDP Ports: 12000
Private TCP Ports: 12000

-- under Network Options i have NAT Port Mapping Protocol enabled
-- the 'Enable default host at:' field is not checked and no value is entered

One of my questions is how to enable a RANGE of ports on the airport, i.e. 12000-12010


Anything I need to do, besides get a JOB????

Thanks in advance--

Leo

[StuartR]

Hi everyone, hoping to get some help here. Joined JK a few weeks ago and had limited success with audio. I've combed thru every available resource i can find on this site and others, but i'm still having difficulty setting up port forwarding on my airport to solve the 'no audio' issues i always run into. also getting the warning that my network changes packets/port numbers when i boot up the app. here's what i have so far:

GEAR
iMac running 10.12.6
Apogee ONE interface
Apple Airport Extreme (w/Ethernet)

-- on PortChecker, the ISPs match so that's 👍
-- Router Mode: DHCP and NAT
-- Port Settings: I set up an IPv4 port mapping setting and named it JK (duh)
Public UDP Ports: 12000
Public TCP Ports: 12000
Private IP Address: 10.0.1.201
Private UDP Ports: 12000
Private TCP Ports: 12000

-- under Network Options i have NAT Port Mapping Protocol enabled
-- the 'Enable default host at:' field is not checked and no value is entered

One of my questions is how to enable a RANGE of ports on the airport, i.e. 12000-12010


Anything I need to do, besides get a JOB????

Thanks in advance--

Leo

Google is your friend:


https://portforward.com/apple/airport-extreme/

[nycbassguy@gmail.com]

Hi everyone, hoping to get some help here. Joined JK a few weeks ago and had limited success with audio. I've combed thru every available resource i can find on this site and others, but i'm still having difficulty setting up port forwarding on my airport to solve the 'no audio' issues i always run into. also getting the warning that my network changes packets/port numbers when i boot up the app. here's what i have so far:

GEAR
iMac running 10.12.6
Apogee ONE interface
Apple Airport Extreme (w/Ethernet)

-- on PortChecker, the ISPs match so that's 👍
-- Router Mode: DHCP and NAT
-- Port Settings: I set up an IPv4 port mapping setting and named it JK (duh)
Public UDP Ports: 12000
Public TCP Ports: 12000
Private IP Address: 10.0.1.201
Private UDP Ports: 12000
Private TCP Ports: 12000

-- under Network Options i have NAT Port Mapping Protocol enabled
-- the 'Enable default host at:' field is not checked and no value is entered

One of my questions is how to enable a RANGE of ports on the airport, i.e. 12000-12010


Anything I need to do, besides get a JOB????

Thanks in advance--

Leo

Google is your friend:


https://portforward.com/apple/airport-extreme/

---

thanks for the tip.
went to the site, and from the looks of it, their screenshots are from older versions of the airport utility than mine, v7.8.1. also, my question specifically was how to enter a RANGE of ports as instructed by JK. appreciate the response.